Concrete is one of the most popular surfaces for commercial and residential use in Snellville Georgia. Because of its durability and low maintenance, homemakers prefer it to other outdoor surface materials.
However, like everything else that is constantly exposed to adverse weather conditions, concrete deteriorates over time. Since you first installed the concrete, it looked positively new. After a few years, what was once shiny gray surface had turned into a dull, monotonous gray.
Other than tearing out the whole concrete surface and replacing it with a new one (which can be an expensive endeavor, not to mention physically taxing), your other option is patio concrete staining. Hiring a professional decorative concrete contractor in Snellville to repair and resurface the concrete if it needs it is well worth the money.
Once the concrete is ready for its first application you have to choose from either acid stains or acrylic stains. Both can greatly enhance the appearance of your concrete surfaces. However, each stain type has its own character and distinction from the other, so it is best if you get to know what the strong and weak points of each type are before making a decision.
What makes outdoor concrete staining using acid stains unique is that every acid type reacts different to the free lime. So you can create different effects, producing an illusion of variety on your surfaces.
The other type of stain used for outdoor concrete staining is acrylic. Because acrylic stains are water-based, the pigments tend to enter through the pores of the concrete surface. In this way, the color, which is characteristically semi-translucent adheres to the concrete in a way that acid stains never do, creating a more lasting and consistent coloring.
The good thing about acrylic stains for outdoor concrete staining is that they can mask any flaws or inconsistencies in the surface. Acid stains, on the other hand, tend to accentuate them.
Epoxy Flooring - Characteristics and Benefits
Concrete stamping has been known to be one of the best ways one can use to decorate their concrete structures. However, the concrete stamping cost can vary from one design to another. There are different designs and colors one can use for concrete stamping. They can range from a few hundred dollars to thousands of dollars.
There are very many factors that will contribute to the concrete stamping cost. Some of the factors are the ones that are listed below. Weather should be something that you should be keen on. This is because rain can ruin the concrete stamping process that you are undertaking. Be sure to have a rough idea of the weather for the days to come.
Cement should be used on a minimum of five sacks. Use of less cement will lead to poorly stamped concrete. The job may then have to be redone to improve its outlook. The redoing will mean greater expenses than normal.
If you are not going to do the job yourself, make sure that you hire decorative concrete professionals in [post_name], who have experience in this line of work. They will be able to tell you where to buy the necessary materials at competitive market prices. They will also be able to guide you on what amount of items such as hardeners or paints so that you do not purchase materials that will not be needed. You will find that the concrete stamping cost can be able to be reduced significantly with proper planning and use of the above mentioned steps.
Epoxy Floor Coating - The Ultimate Floor Coating Surface
Repairing broken concrete can require some heavy equipment and good strong labor depending on how large the area is that needs to be repaired. This example will be based on a badly damaged driveway or perhaps garage floor. If you do not have a truck available to haul away the damaged concrete, a dumpster may be the cheapest means of removal from the site. Many carters will provide a twenty cubic yard for this debris as long as only pure concrete is placed in the dumpster. The carters trucks can easily lift a dumpster that size filled to water level and they can resell the broken concrete to a local landfill for roads or someone using it for fill materials. Reinforcing bars and wire must be removed as much as possible and absolutely no household garbage of any kind is allowed.
Concrete floors and driveways will require the use of a jack hammer to break the concrete into workable sized pieces. Small areas may be done with an electric hammer but thick reinforced slabs and large areas are going to require the use of an air compressor driven hammer or hammers.
Rental shops will have a tow behind unit, hoses and hammers with bits. Ninety pound hammers are the best but they are a bear to handle. Sixty pound hammers are available but of course will not do the work of the bigger hammers. The larger the jack hammer, the faster the demolition work will proceed. Always wear eye and hearing protection when operating a jack hammer. Start by cracking the concrete at the furthest edge of work area away from the dumpster. You will then be able to run the wheelbarrow over a fairly smooth surface to the dumpster instead of over broken concrete or rough ground. If you are repairing or replacing only a portion of the concrete slab you will need to saw cut the slab before removal of the damaged concrete can begin. Using a cut-off saw with a concrete cutting blade, and as neatly as possible, cut a square around the damaged area. Try to penetrate all the way through the slab if possible. Cutting through will sever any reinforcing bars or wire mesh in the slab making removal of the debris much easier.
If you have some latex adhesive made for patching concrete you can paint the exposed face of the slab about one hour before you pour the new concrete. Just minutes before pouring the new concrete, wet the soil below the slab to prevent premature drying of the new concrete. Dry earth will suck all the water out of the fresh concrete much too quickly causing the concrete to shrink.
Pouring the concrete is the easiest and most rewarding part of the job. Once poured, try to prevent the fresh concrete from drying too quickly by placing a tarp over the area for shade or once set and finished, by keeping water over the area for a few days. Wet burlap works great and is easy to soak with a hose. Avoiding premature drying will prevent the patch from shrinking it's edges away from the existing floor edges, leaving an unsightly patch job.