Concrete is one of the most popular surfaces for commercial and residential use in Pike County Georgia. Because of its durability and low maintenance, homemakers prefer it to other outdoor surface materials.
However, like everything else that is constantly exposed to adverse weather conditions, concrete deteriorates over time. Since you first installed the concrete, it looked positively new. After a few years, what was once shiny gray surface had turned into a dull, monotonous gray.
Other than tearing out the whole concrete surface and replacing it with a new one (which can be an expensive endeavor, not to mention physically taxing), your other option is patio concrete staining. Hiring a professional decorative concrete contractor in Pike County to repair and resurface the concrete if it needs it is well worth the money.
Once the concrete is ready for its first application you have to choose from either acid stains or acrylic stains. Both can greatly enhance the appearance of your concrete surfaces. However, each stain type has its own character and distinction from the other, so it is best if you get to know what the strong and weak points of each type are before making a decision.
What makes outdoor concrete staining using acid stains unique is that every acid type reacts different to the free lime. So you can create different effects, producing an illusion of variety on your surfaces.
The other type of stain used for outdoor concrete staining is acrylic. Because acrylic stains are water-based, the pigments tend to enter through the pores of the concrete surface. In this way, the color, which is characteristically semi-translucent adheres to the concrete in a way that acid stains never do, creating a more lasting and consistent coloring.
The good thing about acrylic stains for outdoor concrete staining is that they can mask any flaws or inconsistencies in the surface. Acid stains, on the other hand, tend to accentuate them.
Repairing Broken Concrete
Concrete is a very unyielding substance. It can take a lot of wear and tear. Hence, it is ideal for places that are high traffic areas like the car park. Concrete if treated right will last you a long time. If there are any cracks in the concrete make sure you make the correct repairs. Concrete repairs can be a little complicated so make sure you know what you are doing. If you see any small cracks in your concrete see if needs to be fixed. Polyurethane can be used for most repairs.
Though it is a relatively new concept, the usual methods are quite time consuming. In some cases the whole piece will have to be taken out and replaced. Concrete repairs need some time to set properly so ensure that you are able to close off the area if you are planning any repairs. There are also a lot of steps that have to be followed to get it right. These will be a little tough so try and get someone who has done it a couple of times to help you out. However if you feel confident enough to do it yourself, make sure you follow the steps properly. Short term concrete repair products are epoxies, chalking and resins. Though if you are looking for something more long term, then ready to set concretes would be the right choice.
If the concrete is turning flakey this could be because of high traffic in the area. Products are available which will repair the concrete without removing the whole slab. But the whole area will have to be closed till it sets completely to get the best result. Research the best products available before you decide what suits you best and which will be the easiest for you to do yourself.
Epoxy Floor Coating - The Ultimate Floor Coating Surface
Repairing small cracks in Concrete
Clean out the crack with a wire brush to remove dirt and loose stones. Wash the crack with a concrete cleaner. Get commercially available nonacid concrete cleaner made by the same company that makes your patching compound. It is safer and more convenient than the large of muriatic acid masons might use.
Let the surface dry. If the crack is deep and it is in a floor, fill it partially with sand, leaving an opening about 1/4 to 1/2 inch deep. Pour in the crack sealer until it forms a layer 1/4 inch deep. Let it dry overnight and then apply another layer. Repeat until the surface is flush with the floor. Do not overfill, apply enough patch material to bring the surface flush with the floor. If using caulk, smooth with a metal putty knife.
On deeper cracks, mix some sand mix according to the direction on the bag. Trowel it into the cracks, filling it flush with the surface. First, the patch on both deep and shallow cracks will have a watery sheen. When the sheen dries off, se a wooden float to smooth the surface and give it a texture that matches the rest of the concrete. If the existing concrete is very smooth, then smooth the surface with a metal finishing trowel.