Garage Floor Coating Zebulon Georgia

Restaurant Rubber Flooring Zebulon Georgia

Acid Stain For Concrete

Concrete is one of the most popular surfaces for commercial and residential use in Zebulon Georgia. Because of its durability and low maintenance, homemakers prefer it to other outdoor surface materials.

However, like everything else that is constantly exposed to adverse weather conditions, concrete deteriorates over time. Since you first installed the concrete, it looked positively new. After a few years, what was once shiny gray surface had turned into a dull, monotonous gray.

Other than tearing out the whole concrete surface and replacing it with a new one (which can be an expensive endeavor, not to mention physically taxing), your other option is patio concrete staining. Hiring a professional decorative concrete contractor in Zebulon to repair and resurface the concrete if it needs it is well worth the money.

Once the concrete is ready for its first application you have to choose from either acid stains or acrylic stains. Both can greatly enhance the appearance of your concrete surfaces. However, each stain type has its own character and distinction from the other, so it is best if you get to know what the strong and weak points of each type are before making a decision.

Decorative Concrete Overlay

What makes outdoor concrete staining using acid stains unique is that every acid type reacts different to the free lime. So you can create different effects, producing an illusion of variety on your surfaces.

The other type of stain used for outdoor concrete staining is acrylic. Because acrylic stains are water-based, the pigments tend to enter through the pores of the concrete surface. In this way, the color, which is characteristically semi-translucent adheres to the concrete in a way that acid stains never do, creating a more lasting and consistent coloring.

The good thing about acrylic stains for outdoor concrete staining is that they can mask any flaws or inconsistencies in the surface. Acid stains, on the other hand, tend to accentuate them.


Previous | Next


Decorative Concrete Resurfacing

Restaurant Flooring Options

Repairing broken concrete can require some heavy equipment and good strong labor depending on how large the area is that needs to be repaired. This example will be based on a badly damaged driveway or perhaps garage floor. If you do not have a truck available to haul away the damaged concrete, a dumpster may be the cheapest means of removal from the site. Many carters will provide a twenty cubic yard for this debris as long as only pure concrete is placed in the dumpster. The carters trucks can easily lift a dumpster that size filled to water level and they can resell the broken concrete to a local landfill for roads or someone using it for fill materials. Reinforcing bars and wire must be removed as much as possible and absolutely no household garbage of any kind is allowed.

Concrete floors and driveways will require the use of a jack hammer to break the concrete into workable sized pieces. Small areas may be done with an electric hammer but thick reinforced slabs and large areas are going to require the use of an air compressor driven hammer or hammers.

Rental shops will have a tow behind unit, hoses and hammers with bits. Ninety pound hammers are the best but they are a bear to handle. Sixty pound hammers are available but of course will not do the work of the bigger hammers. The larger the jack hammer, the faster the demolition work will proceed. Always wear eye and hearing protection when operating a jack hammer. Start by cracking the concrete at the furthest edge of work area away from the dumpster. You will then be able to run the wheelbarrow over a fairly smooth surface to the dumpster instead of over broken concrete or rough ground. If you are repairing or replacing only a portion of the concrete slab you will need to saw cut the slab before removal of the damaged concrete can begin. Using a cut-off saw with a concrete cutting blade, and as neatly as possible, cut a square around the damaged area. Try to penetrate all the way through the slab if possible. Cutting through will sever any reinforcing bars or wire mesh in the slab making removal of the debris much easier.

If you have some latex adhesive made for patching concrete you can paint the exposed face of the slab about one hour before you pour the new concrete. Just minutes before pouring the new concrete, wet the soil below the slab to prevent premature drying of the new concrete. Dry earth will suck all the water out of the fresh concrete much too quickly causing the concrete to shrink.

Pouring the concrete is the easiest and most rewarding part of the job. Once poured, try to prevent the fresh concrete from drying too quickly by placing a tarp over the area for shade or once set and finished, by keeping water over the area for a few days. Wet burlap works great and is easy to soak with a hose. Avoiding premature drying will prevent the patch from shrinking it's edges away from the existing floor edges, leaving an unsightly patch job.


Reducing Concrete Stamping Cost

Concrete Acid Stain Colors

Repairing small cracks in Concrete

Clean out the crack with a wire brush to remove dirt and loose stones. Wash the crack with a concrete cleaner. Get commercially available nonacid concrete cleaner made by the same company that makes your patching compound. It is safer and more convenient than the large of muriatic acid masons might use.

Let the surface dry. If the crack is deep and it is in a floor, fill it partially with sand, leaving an opening about 1/4 to 1/2 inch deep. Pour in the crack sealer until it forms a layer 1/4 inch deep. Let it dry overnight and then apply another layer. Repeat until the surface is flush with the floor. Do not overfill, apply enough patch material to bring the surface flush with the floor. If using caulk, smooth with a metal putty knife.

On deeper cracks, mix some sand mix according to the direction on the bag. Trowel it into the cracks, filling it flush with the surface. First, the patch on both deep and shallow cracks will have a watery sheen. When the sheen dries off, se a wooden float to smooth the surface and give it a texture that matches the rest of the concrete. If the existing concrete is very smooth, then smooth the surface with a metal finishing trowel.


[tag] Zebulon Georgia